ECET 365 DeVry Complete Quiz Package

admin   June 29, 2017   Comments Off on ECET 365 DeVry Complete Quiz Package

ECET 365 DeVry Complete Quiz Package

Downloading is very simple, you can download this Course here:

http://wiseamerican.us/product/ecet-365-devry-complete-quiz-package/

Or

Contact us at:

SUPPORT@WISEAMERICAN.US

ECET 365 DeVry Complete Quiz Package

ECET365

ECET 365 DeVry Week 2 Quiz

  1. Question :(TCO #5)Identify the step size for an 8-bit analog-to-digital converter with Vref= 2.5 VDC?
  • 10 millivolts
  • 25 millivolts
  • 4.9 millivolts
  • 5 volts
  1. Question :(TCO # 5)How many steps are available with a 10-bit ADC?
  • 10
  • 1024
  • 512
  • 256
  1. Question :(TCO #5)What is the cutoff frequency for a low-pass filter with a resistor R = 3000 and a capacitor C = .01 µf?
  • f = 5.3 KHz
  • f = 3300 Hz
  • f = 120 KHz
  • f = 6 KHz
  1. Question :(TCO #5)A band-stop filter is a filter that _____ frequencies below low-limit and above high-limit frequencies and _____ frequencies between the limits.
  • blocks; blocks
  • passes; blocks
  • blocks; passes
  • has; blocks
  1. Question :(TCO #5)A bridge with R1= 5.1 K, R2= 2 K, and R3= 15 K can be at null if R4is _____.
  • 10.5 K
  • 5.88 K
  • 588
  • 1 K
  1. Question : (TCO #5)An instrumentation amplifier with two buffers has a feedback resistor of 100 K. The two resistors from the buffer’s output to the input of the last stage OP-Amp are 1 K resistors. Voltage levels to the non-inverting buffer inputs. Voltage levels to the non-inverting buffer inputs are V1= .06 volt and V2= .02 volts. What is Voutof the instrumentation amplifier?
  • 4 Volts
  • 20.4 Volts
  • 3.3 Volts
  • 15.3 Volts
  1. Question : (TCO #5)An embedded system with an 8-bit analog-to-digital converter is connected to a transducer with an output voltage of 10 millivolts. This signal is amplified by an amplifier with a gain of 25. Assume that this signal level is appropriate for the ADC input. If the reference voltage of the ADC converter is 5 volts, what will be the output of the ADC in binary form?
  • 01100110
  • 00110011
  • 00001101
  • 01111011
  1. Question: (TCO #5)An 8-bit analog-to-digital converter has maximum output voltage of 2.5 VDC. What is the reference voltage to this ADC?
  • 2.5 VDC
  • 5 VDC
  • 1.25 VDC
  • None of the above
  1. Question : (TCO #5)A well-behaved analog signal with a frequency of 20 kHz is being sampled. What is the sampling frequency if frequency aliasing occurs?
  • 90 kHz
  • 40 kHz
  • 85 kHz
  • 60 khz
  1. Question : (TCO #5)To model a nonlinear transducer, one can _____.
  • use empirically determined nonlinear equation
  • use a piecewise linear system
  • use a lookup table located in memory
  • All of the above

 

 

ECET 365 DeVry Week 3 Quiz

  1. Question : (TCO #3)Which interrupt is non-maskable?
  • Software interrupt (SWI)
  • Interrupt from a device connected to IRQ pin of HCS12 microcontroller
  • Both A and B
  • Interrupt by multiple devices connected to IRQ pin of HCS12 microcontroller
  1. Question : (TCO #3)Which of the following interrupts has the highest priority?
  • TCNT timer overflow
  • SCI0
  • ATD0
  • ATD1
  1. Question : (TCO #3)Which selection is connected to the reset module in the HCS12 microcontroller?
  • Reset pin
  • ADC0
  • ADC1
  • None of the above
  1. Question : (TCO #3)Which bit can mask a maskable interrupt?
  • S bit
  • Z bit
  • N bit
  • None of the above
  1. Question : (TCO #3)In the HCS12 microcontroller, the address range 0xFFFE – 0xFFFF in the interrupt vector table is assigned to which of the following?
  • Clock monitor fail reset
  • ATD0
  • Reset
  • COP failure reset
  1. Question : (TCO #3)Freescale utilizes BDM to _____.
  • check each instruction of a program individually
  • reset CPU by setting IRQ pin to high-level logic
  • check changes in memory and CPU register for each instruction execution
  • Both A and C
  1. Question : (TCO #3)Watch dog timer is a utility that _____.
  • can reset the microcontroller whenever a program locks up.
  • can catch errors due to memory corruption
  • makes sure that a program does go to an unintentional infinite loop sequence
  • Both A and B
  1. Question : (TCO #3) When an interrupt occurs, _____.
  • in one stage, the contents of the CPU move to RAM memory
  • the CPU finishes executing its current instruction before it starts running an interrupt thread
  • all interrrupts will be ignored if the I bit is zero
  • Both A and B
  1. Question : (TCO #3)Which combination is an appropriate way of setting up the PORTJ interrupt to enabled?
  • Pin I of CCR = 0
  • Pin I of CCR = 1
  • Pin I of CCR = 1 and PIEJ7 = 1
  • Pin I of CCR = 0 and PIEJ6 = 0
  1. Question : (TCO #3)Which of the following interrupts has the highest priority immediately after a microcontroller reset?
  • Reset
  • XIRQ
  • COP
  • All have the same level of priority.

 

 

ECET 365 DeVry Week 4 Quiz

  1. Question : (TCO #1, 2, and 7)Select the header file in CodeWarrior for the Freescale MC9s12DG256.
  • mc9s12dg256.h
  • mc9s12dg256.header
  • mc9s12dg256.asm
  • mc9s12dg256
  1. Question : (TCO #1, 2, and 7)_____ is part of the UNIX OS user layer.
  • API
  • Device driver
  • Shell
  • Core
  1. Question : (TCO #1, 2, and 7)A multitask operating system is more feasible in _____.
  • an embedded system
  • a computer with multiple processors
  • a processor with two accumulators
  • a computer with multiple hard disks
  1. Question : (TCO #1, 2, and 7)In layered software architecture, the main module is usually found within _____.
  • the last (lowest) layer
  • the API
  • the first (top) layer
  • a module inside a thread
  1. Question : (TCO #1, 2, and 7)The user of a module may be interested in _____.
  • passing values to the module
  • the output format of the module
  • who wrote the module
  • Both A and B
  1. Question : (TCO #1, 2, and 7)Identify the computer language commonly used for embedded programming.
  • C
  • Assembly
  • Both A and B
  • Pascal
  1. Question : (TCO #1, 2, and 7)Which of the following commands loads hexadecimal number 44 to accumulator A?
  • LDAA #$44
  • LDAA #44
  • LDA #44
  • LDAA 44$
  1. Question : (TCO #1, 2, and 7)C ++ encapsulation is _____.
  • grouping functions and variables into one class
  • grouping only functions in one class
  • grouping only variables in one class
  • grouping functions and variables in multiple classes
  1. Question : (TCO #1, 2, and 7)Information shared by multiple program modules is known as _____.
  • a static int
  • a global variable
  • a local variable
  • a function
  1. Question : (TCO #1, 2, and 7)A multichannel digital storage scope is known as _____.
  • an ICE
  • a logic analyzer
  • a spectrum analyzer
  • a network analyzer

 

 

ECET 365 DeVry Week 5 Quiz

  1. Question : (TCO #5)In an asynchronous data transfer _____.
  • the transmitter and receiver clock must be exactly the same all the time
  • the receiver clock must be exactly the same or multiple times the transmitter clock
  • it is not necessary to have a clock in the receiver
  • None of the above
  1. Question : (TCO #5)Synchronization between data transmitter and receiver _____ data transfer.
  • is necessary in asynchronous
  • is necessary in synchronous
  • is necessary in both asynchronous and synchronous data transfer
  • is not necessary in both an asynchronous and synchronous
  1. Question : (TCO #5)Which register is utilized in setting the baud rate in a SCI interface?
  • SCIBDH
  • SCI0CR2
  • SCI0BDL
  • Both A and C
  1. Question : (TCO #5)To sample data at the falling edge of the clock when using SPI, _____.
  • CPA in SPICR1 must be 0
  • MSTR in SPICR1 must be 0
  • CPA in SPICR1 must be 1
  • MSTR in SPICR1 must be 1
  1. Question : (TCO #5)A SPI master IC connects to slave IC with _____.
  • five wires
  • one wire
  • four wires
  • wireless
  1. Question : (TCO #5) Communication between two modems through telephone lines is _____.
  • serial
  • parallel
  • digitalall the time
  • Both A and C
  1. Question : (TCO #5)SPI implements a/an _____ protocol.
  • asynchronous
  • synchronous
  • parallel
  • TCP
  1. Question : (TCO #5)In full-duplex data transfer, _____.
  • data transfer from the transmitter only
  • data bits transfer simultaneously in both directions
  • data bits transfer in both directions but not simultaneously
  • data bits transfer in a parallel bus
  1. Question : (TCO #5)High voltage level in a TTL chip is _____.
  • 12 volts
  • 5 volts
  • -5 volts
  • -12 volts
  1. Question : (TCO #5)USB utilizes _____.
  • a serial data transfer
  • a parallel data transfer
  • a mixed parallel/serial data transfer
  • a daisy chain to connect maximum of 10 devices

 

 

ECET 365 DeVry Week 6 Quiz

  1. Question : (TCO #6)How many 16-bit PWM channels are available in the Freescale 9S12DG256 microcontroller?
  • Two
  • Four
  • Seven
  • Eight
  1. Question : (TCO #6)When concatenating the two 8-bit PWM Channels 3 and 2 to get a 16-bit PWM channel, _____ becomes the low-order byte.
  • Channel 7
  • Channel 2
  • Channel 5
  • Channel 3
  1. Question : (TCO #6)To enable Channel 7 of the PWM to 9S12DG256, which of the following must be done?
  • Set PWME7 = 1
  • Set PWME7 = 0
  • Set CAE7 = 1
  • Set CAE7 = 0
  1. Question : (TCO #6)What is Clock SA when PWMSCLA = 0×01 and Clock A = 4MHz?
  • 5MHz
  • 4MHz
  • 8MHz
  • 2MHz
  1. Question : (TCO #6)What is Clock SA when PWMSCLA = 0×00 and Clock A = 8MHz?
  • 8MHz
  • 15625Hz
  • 8MHz
  • 31250Hz
  1. Question : (TCO #6)A bus clock is set to 4000 kHz. What is the Clock A’s value if PWMPRCLK = 0×02?
  • 1MHz
  • 3MHz
  • 2MHz
  • 8MHz
  1. Question : (TCO #6)In case of center-aligned PWM, which formula can be used for the duty cycle of the output waveform?
  • Duty Cycle = [(PWMPERx – PWMDTYx) / PWMPERx] * 100%
  • Duty Cycle = [PWMDTYx / PWMPERx] * 100%
  • Duty Cycle = PWMDTYx 100%
  • Both A or B (depends on PPOLx)
  1. Question : (TCO #6)In case of center-aligned PWM, which formula can be used for the PWM frequency?
  • PWMx frequency = Clock (A, B, SA, or SB) / PWMPERx
  • PWMx frequency = Clock (A, B, SA, or SB) / (2 * PWMPERx)
  • PWMx frequency = Clock (A, B, SA, or SB) / (4 * PWMPERx)
  • PWMx frequency = Clock (A, B, SA, or SB) / (3 * PWMPERx)
  1. Question : (TCO #6)Current passing through a wire creates an electromagnetic field that _____.
  • loops around the wire
  • is directly proportional to the amount of the current flowing inside the wire
  • is strongest closer to the wire
  • satisfies all of the above answers
  1. Question : (TCO #6)PWM channels of a microcontroller are designed for control of a _____.
  • servo motor
  • AC motor
  • stepper motor
  • None of the above